Submersible Vertical Turbine Pumps

Bell & Gossett : Pumps & Circulators : Vertical Turbine Pumps

Hermetically Sealed Type
A Hermetically Sealed Type motor utilizes windings of standard construction and insulation thickness. The windings are encased and Hermetically Sealed within the external shell casing on the outside and an internal tube or liner inside the bore. The Hermetically Sealed enclosure eliminates the possibility of water leakage into the winding. The liquid medium circulates between the rotor and stator liner providing lubrication and cooling to the bearings.

Wet Winding Type
A Wet Winding Type motor is one in which the motor windings are in direct contact with a liquid medium. The medium is clean, clear water. A pressure balancing system prevents exchange of the motor liquid medium and well water due to thermal expansion and contraction when the motor is operating. The liquid medium fills the inside of the motor and surrounds both the stator windings and the rotor. A completely waterproof insulation is used on the magnet wire used for the stator windings. The liquid medium inside the motor air gap and coils acts as a heat transfer device by circulating through the windings and transferring heat to the external casing. Dissipation of this heat occurs as the well water flows at a required velocity over the external case. As is the case in all submersible type motors, the internal liquid medium is also used for bearing lubrication.

Submersible Options:
Bell & Gossett can provide several options in pump and motor combinations to meet the exacting conditions of your applications:
· High horsepower, limited well diameters.
· Motor sensing devices.
· Water level indicators.
· Special materials.
· Special voltage motors.

APPLICATIONS:
COOLING TOWERS, PRESSURE BOOSTING AND GENERAL WATER SERVICE.

Features and Benefits

  • Discharge Pipe – Properly sized for optimum water velocities to insure peak hydraulic performance.
  • Discharge Bowl – Several discharge sizes available for NPT or flanged pipe.
  • Discharge Bearing – Extra long top protected bronze bearing insures positive shaft alignment and stabilization for extended life.
  • Intermediate Bowl – Close grained Class 30 cast iron. Water passage glassed for maximum efficiency and abrasion resistance.
  • Impellers – Designed for maximum efficiency with wide range hydraulic cover age. Precision balanced for smooth operation.
  • Upthrust Collar – Designed for extra margin of safety against possible momentary upthrust occurring at startup.
  • Intermediate Bowl Bearings – Reliable long life bronze or rubber bearing.
  • Lock Collets – Accurately machined to insure positive locking of pump impeller to shaft.
  • Pump Shaft – 100,00 PSI high tensile stainless steel provides strength and excellent corrosion resistance. Ground and polished for smooth bearing surface.
  • Suction Inlet – Contoured for smooth flow entrance. Protected by an over sized stainless steel strainer to prevent entrance of damaging solids.
  • Suction Adapter – Ductile iron provides for increased strength and positive motor alignment. Open area permits easy access to pump/motor coupling.
  • Pump/Motor Coupling – Large stainless steel coupling accurately machined for perfect alignment, balance, and power transmission.

Brochures

    General Selection Tools:

    • ESP-PLUS for B&G Centrifugal Pumps, Booster Pumps, Pump Accessories, and Air Separator
    • ESP-PARTS for replacement parts selection
    • ESP-TANKS for replacement parts selection
    • CAD Drawings for 2D and 3D dimensional drawings in many formats

    Heat Exchanger Product Selection

    Steam + Water Pressure Reducing Values

    Sizing Tools:

    Report Bugs/Request Enhancements
    Please email the following address to report issues and request enhancements: ebusiness.support@xyleminc.com

    Consult your local Bell & Gossett Representative for additional assistance.

    Xylem Water Systems Australia Pty. Ltd
    Unit 3/1 Federation Way,
    Chifley Business Park
    3194 Mentone Victoria
    Australia
    Tel. +61 3-95517333
    Fax +61 3-95510321
    Australia Distributors

    Queensland
    Brown Brothers Engineers
    50 Nestor Drive
    Meadowbrook QLD 4131
    Phone:07 3200 6488
    Fax:07 3200 3822
    New South Wales and Australian Capital Territory
    Brown Brothers Engineers
    211-215 Walters Rd
    Arndell Park NSW 2148
    Phone:02 9671 3666
    Fax:02 9671 3644
    Victoria and Tasmania
    Brown Brothers Engineers
    8 Damien Court
    Dandenong Vic 3175
    Phone:03 9793 9999
    Fax:03 9793 0022
    Western Australia
    Advanced Pump Technologies
    72 May Holman Drive
    Bassendean WA 6054
    Ph: 08 6143 1000
    Fx: 08 6143 1009
    South Australia and Northern Territory
    WBS Pumps
    6A Lasalle Street
    Dudley Park SA 5008
    Phone:08 8344 9927
    Fax:08 8344 9925
    New Zealand Distributors
    Christchurch (head office)
    Brown Brothers Engineers
    197 Durham Street
    Christchurch 8011
    New Zealand
    Phone: 3 365 0279
    Fax: 3 366 6616
    Dunedin
    Brown Brothers Engineers
    10 Timaru Street
    Dunedin 9012
    New Zeland
    Phone: 3 456 2562
    Fax: 3 456 2564
    Timaru 
    Brown Brothers Engineers
    Unit 6/39 North Street
    Timaru 7910
    New Zealand
    Phone: 3 683 1686
    Fax: 3 683 1687
    Auckland
    Brown Brothers Engineers
    124A Hugo Johnston Drive
    Penrose, Auckland 1061
    New Zealand
    Phone: 9 525 8282
    Fax: 9 525 8284
    Hamilton
    Brown Brothers Engineers
    97C Norton Road
    Frankton, Hamilton 3204
    New Zeland
    Phone: 7 847 5280
    Fax: 7 847 1580
    Wellington
    Brown Brothers Engineers
    9 Aglionby Street
    Lower Hutt, Wellington 5010
    New Zealand
    Phone: 4 570 1500
    Fax: 4 570 1499